Download Canon Service Tool V 4718 Resetter 2021

The Canon Service Tool v4718 is a specialized maintenance utility used to resolve critical hardware-lock errors, most notably the "Waste Ink Absorber Full" error (often indicated by codes 5B00 or 1700). Unlike the standard Maintenance Tool included with drivers, this service-level software communicates directly with the printer's EEPROM to reset internal counters. Key Features of v4718

Ink Absorber Reset: Clears the waste ink counter value to zero, allowing the printer to resume operation after physical maintenance.

Error Code Fixes: Specifically addresses errors such as 5B00, 5B02, 5B04, 5B14, 1701, and 1702.

EEPROM Management: Allows users to print or save current EEPROM data to verify printer health and settings before and after resets.

Regional Configuration: Provides options to "Set Destination" for specific markets including USA, EUR (Europe), ASA (Asia), and others. Supported Printer Models

While official documentation is scarce, community reports and guides from PrinterKnowledge and Scribd indicate compatibility with: G Series: G1000, G2000, G3000 series.

MG Series: MG3500, MG3600, MG5500, MG5600, MG5700, MG6400, MG6600, and MG6800 series.

Legacy Pixma: Various iP, MP, and MX models that support the standard 5-click service mode entry. How to Use the Resetter

Using the tool requires the printer to be in Service Mode. Follow these general steps:

Enter Service Mode: With the printer off, hold the Stop button and then press and hold Power. While holding Power, press the Stop button 5 times (this may vary by model) and release both buttons.

Run the Tool: Download the portable software from sources like Printkita or Yandex. Open Canon Service Tool V4718.exe while your printer is connected via USB.

Reset Counter: In the "Clear Ink Counter" section, select Main and click Set. The printer will usually print a confirmation page showing the counter is now 0. Critical Safety Warnings

Service Tools for Canon Printers | Page 5 | PrinterKnowledge

I understand you're looking for information about the Canon service tool v4718 resetter, but I need to provide some important context first.

Canon service tools (including v4718) are proprietary software intended for authorized Canon service centers. These tools are not officially distributed to end users because they can:

1. Permanently damage your printer if used incorrectly
2. Void your warranty
3. Bypass safety mechanisms and counter resets that exist for good engineering reasons

The v4718 tool in particular is used to reset waste ink counters on certain Canon printers after the waste ink absorber pads become full. However, Canon designs these pads to be replaced—not just reset—because saturated pads can leak ink and damage the printer or your work area.

What you should do instead:

• For waste ink issues: Contact Canon support or an authorized service center for proper pad replacement and reset
• For general maintenance: Check Canon's official maintenance software for your model
• If you're a technician: Obtain the tool through proper Canon service channels with appropriate certification

If you choose to search for this tool elsewhere (not recommended):

Proceed with extreme caution—many "free download" sites for service tools host malware, keyloggers, or ransomware. No legitimate source distributes these tools publicly.

Bottom line: There's no safe, legal write-up I can provide for downloading or using this unauthorized tool. I'd recommend pursuing the official service route to avoid damaging your printer or exposing your computer to security risks.

Would you like help finding authorized Canon support options for your specific printer model instead?

Canon Service Tool v4718 is a specialized Windows utility used to diagnose and maintain select Canon inkjet printers. It is most commonly used to reset the waste ink absorber counter (Error Code 5B00). Key Features and Support

: Resets "Ink Absorber Full" errors, clears internal error logs, and performs hardware diagnostics. Compatible Models : Primarily supports the , G3000) and some Operating System

: Requires a Windows-based PC (XP, 7, 8, or 10) and a direct USB connection to the printer. How to Use Canon Service Tool v4718

Before the software can communicate with your printer, you must manually put the device into Service Mode Step 1: Enter Service Mode

Service Tools for Canon Printers | Page 4 - PrinterKnowledge download canon service tool v 4718 resetter

The Canon Service Tool v4718 is a specialized maintenance utility used to reset the internal "waste ink absorber" counter and clear system errors like 5B00 or P07. While it is highly effective for extending the life of a printer, it is not an official public download from Canon and carries specific risks. Core Functionality

Waste Ink Counter Reset: Its primary use is resetting the "absorber" counter to 0% after a printer stops working due to being "full".

Maintenance Features: Allows users to print EEPROM information, perform nozzle checks, and update firmware.

Service Mode Requirement: The software only works if the printer is first placed in a specific "Service Mode" (typically involving a sequence of power and stop button presses). Key Performance Insights

High Success Rate for Specific Models: Users report successful resets for popular series like the MG3500, MG3600, and G-series (e.g., G1000, G2000).

Portability: It is often distributed as a "portable" application, meaning it does not require a formal installation on Windows.

Compatibility Limits: It may not work with newer Canon models (post-2018), which sometimes require even newer versions like v5103 or v6310. Critical Risks & Considerations

The Ghost in the Printer

Leo typed the words into a cracked phone at 2 a.m.: download canon service tool v 4718 resetter.

His Canon printer had flashed its dreaded "waste ink pad full" error three days ago—right before his final project was due. The printer was otherwise perfect. Leo couldn't afford a new one, and the official service center wanted more than his rent.

The link he clicked led to a forum that looked like it hadn't been updated since 2009. Buried under pop-ups for "driver updater 2020" was a zip file: ServiceTool_V4718.rar.

No password. No readme. Just the .exe.

Leo disabled his antivirus—the warning said it would flag it as a hack tool. "Well," he muttered, "that's technically true."

The software opened like a relic from Windows XP. Gray boxes. Broken English labels. A single button: Main Reset.

He connected the printer via USB. Clicked.

The printer whirred to life—grinding, clicking, then silence. The error light went off. Leo exhaled.

But then the printer spat out a single page. Not blank. In tiny, near-illegible type:

"I remember everything you printed. But I'll keep your secret. For now."

Leo stared. He printed a test page. Normal. He printed another. Fine. He never saw that message again.

But sometimes, late at night, the printer would wake up on its own—just a soft hum, like it was thinking. And Leo would wonder: what kind of reset had he really performed?

Disclaimer: This is fiction. In reality, using unofficial service tools can damage devices or violate warranties. Always proceed with caution and at your own risk.

The Canon Service Tool v4718 is a specialized maintenance software used primarily to reset the waste ink counter (also known as the ink absorber counter) on various Canon PIXMA and MAXIFY printers . This becomes necessary when a printer displays errors like 5B00 or 1700, which indicate the internal ink pads are theoretically full . Key Functions of v4718

Beyond resetting counters, this tool is used for several low-level maintenance tasks:

Clear Ink Counter: Resets the waste ink absorber percentage to 0% .

EEPROM Management: Allows users to view, save, or clear EEPROM data to diagnose internal hardware issues . The Canon Service Tool v4718 is a specialized

Test Prints: Performs nozzle checks and deep cleaning cycles directly through the service interface .

Set Destination: Changes the region settings of the printer . Compatible Models

While Canon does not provide an official public list for this version, community evidence suggests it supports:

MG Series: Popularly used for the MG3500 series (specifically confirmed for MG3550) .

G Series: Often used for "Mega Tank" models like the G1000 through G4000 series .

Older Models: Generally supports printers from the PGI-x50/CLI-x51 cartridge era and earlier . How to Use the Resetter

Using the tool requires the printer to be in Service Mode. This typically involves a specific button sequence:

Service Tools for Canon Printers | Page 5 | PrinterKnowledge

I understand you're looking for information about the Canon Service Tool v4718 (often called a resetter), typically used to reset ink absorber counters or waste ink pads on certain Canon printers.

However, I must caution you:

• Official Canon service tools are intended for authorized service centers. Downloading them from third-party sites often violates Canon's terms of use.
• Many "free downloads" of v4718 contain malware, viruses, or keyloggers — especially on forums, torrent sites, or file-sharing hosts.
• Using such tools incorrectly can permanently damage your printer's firmware or render it inoperable.

If your printer is displaying a "waste ink pad full" or service error (e.g., 5B00, 5B01), a safer approach is:

1. Clean or replace the waste ink pads manually (many guides online).
2. Use legitimate software like WIC Reset Utility (paid but reputable) or contact a local printer service.
3. Check if your printer model officially supports resetting via button combinations — some newer models do.

⚠️ I will not provide direct download links to v4718 or other cracked service tools due to security and legal risks.

If you still choose to search for it, run any downloaded file through VirusTotal first, use a sandboxed environment, and never run it on a computer with sensitive data.

Canon Service Tool v4718 is a specialized software utility used by technicians to perform deep-level maintenance on Canon printers, most notably for resetting the waste ink absorber counter (Error 5B00) after physical cleaning or replacement. Software Report: Canon Service Tool v4718 Primary Function

: Resets ink counters, clears internal service errors, and updates firmware. Key Feature

: Specifically capable of resetting the "pampers" (absorber) counter on various models where newer versions like v5103 may fail with "Error 006". Supported Models : Compatible with (G1000, G2000, G3000), (MG3500, MG3600), and others including iP7240. Portability

: This is a standalone executable (portable) and does not require a standard Windows installation. Critical Usage Instructions To use the tool, the printer must first be in Service Mode

. Using the software in normal "User Mode" will result in a connection error. Enter Service Mode

Power off the printer but keep it connected via USB (wireless reset is not supported). Stop/Reset button (triangle icon) and then press and hold While holding and press it

Release both buttons. Wait for the power light to stay steady. Reset Procedure Open the v4718 utility on a Windows PC. "Clear Ink Counter" "Ink Absorber Counter" section, select

. A confirmation page should print or a "Success" message will appear. Safety & Source Warnings

Canon Service Tool v4718 a specialized utility designed for authorized service technicians to perform deep maintenance on Canon printers, such as clearing Error 5B00 and resetting the waste ink absorber counter

. While it can be a lifesaver for extending a printer's life, using it carries significant risks, including permanently "locking" the printer's service mode or infecting your computer with malware from unofficial download sources. Key Features & Capabilities Waste Ink Counter Reset:

Its primary use is resetting the ink absorber counter after you have physically cleaned or replaced the pads. EEPROM Operations:

It can read and print EEPROM information, which provides a detailed history of the printer's usage. Print Head Maintenance: Permanently damage your printer if used incorrectly Void

Allows for deep cleaning and nozzle checks that go beyond standard consumer driver options. Error Clearance:

Useful for clearing certain service-call errors after hardware repairs like logic board replacements. Compatibility

The v4718 version is generally tailored for older Canon models, particularly the G-series and certain PIXMA MG models: G1000, G2000, G3000. MG-Series:

MG3500, MG3600 (though some sources suggest v4713 for these), and older models like the MG5150. It often does

work with newer "one-time use" or strictly protected models like the MG24xx, MG25xx, or TS-series. Risk Assessment & Download Warnings

Downloading this tool requires extreme caution. Because it is not officially distributed to consumers by Canon, available files are often "cracked" or "patched". Google Drive Malware Traps:

Many hosted versions on forums or file-sharing sites (like Google Drive links or password-protected RARs) are flagged as or viruses. Permanent Locking:

If you attempt to use the tool without correctly putting the printer into Service Mode

first, or if you use an incompatible version, you can permanently damage the printer's firmware. Hardware Damage:

Resetting the counter without actually cleaning the waste ink pads can lead to physical ink leaks and damage to your furniture or internal printer electronics. How to Use (High-Level Process)

Service Tools for Canon Printers | Page 5 | PrinterKnowledge

The Canon Service Tool v.4718 is a portable utility used primarily to reset the waste ink absorber counter (Error 5B00) on various Canon PIXMA and G-series printers. Because this tool is a proprietary internal utility not officially released to consumers, it is typically found on third-party forums and community sites rather than the official Canon Support Page . Important Safety Warning

Security Risk: Many "free" downloads of service tools are flagged by antivirus software as potential trojans or malware. Use an isolated "test" computer if possible.

Device Risk: Selecting the wrong setting in the tool can permanently disable (brick) your printer's logic board.

Hardware Warning: Resetting the software counter without physically replacing or cleaning the ink absorbers can lead to actual ink spills inside the device. Compatible Models

The v.4718 version is known to support the following series: G-Series: G1000, G2000, G3000

MG-Series: MG3500, MG3600 (v.4713/4718 reported to work where others fail)

Older Models: Generally works with printers from the PGI-x50/CLI-x51 cartridge generation and earlier. Step 1: Entering Service Mode

Your printer must be in Service Mode for the tool to detect it. This is typically done with a button combination while the printer is off:

Service Tools for Canon Printers | Page 5 | PrinterKnowledge

Q: How many times can I reset with v4718?

Technically unlimited, but physically the waste pad can absorb only about 2-3 resets worth of ink before leaking. After 3 resets, you must replace the pad.

The Physical Reality

Resetting the counter does not empty the sponge. If your printer has printed 15,000 pages and you reset the counter, the sponge is already full of ink. If you continue printing, ink WILL leak out the bottom of the printer, ruining your desk, cables, and potentially starting an electrical fire.

You must physically clean or replace the waste ink pad. This involves disassembling the printer—a task far harder than running the v4718 tool.

Step 3: Scan Before Running

After downloading, absolutely do not open the file yet. Run it through:

• VirusTotal (virustotal.com) – Upload the file. 1-2 detections as “hacktool” are normal; 15+ detections indicate malware.
• Windows Defender / Malwarebytes – Perform a full offline scan.

If the tool is flagged as “Generic.Malware.AI” or Trojan, delete it immediately and find another source.

The Search: "Download Canon Service Tool v4718 Resetter"

Typing this keyword into Google yields a minefield. You will find links on sites like Resetter.ru, PrinterPot, 2manuals, and TinyURL. However, downloading this tool comes with significant digital hygiene risks.