Dvb Select Type Error Samsung Tv < FAST - 2025 >
Errors related to DVB (Digital Video Broadcasting) on Samsung TVs, such as "DVB Select Type" or "New DVB Service Found,"
typically occur when the TV's internal tuner detects changes in the digital signal or when the broadcast settings do not match the input source JustAnswer Common Fixes for DVB Errors
If you are encountering errors or persistent "New DVB Service" messages, try the following: DVB TV Problems - JustAnswer
It sounds like you're encountering a "DVB Select Type Error" on your Samsung TV. This typically happens when the TV's tuner is set to the wrong DVB standard for your region or when scanning for channels.
Here's how to fix it:
Notes on DVB variants and regional differences
- DVB-T2 is widely used for terrestrial HDTV in many countries; some Samsung TVs may require a firmware/region update to support DVB-T2.
- Cable networks may use DVB-C with QAM modulation and sometimes encryption — plain scanning may not reveal encrypted channels.
- Satellite (DVB-S/S2) requires correct LNB type and DiSEqC settings for multi-LNB setups.
3. If you still see the error
- Your TV may be a non-local model (e.g., European Samsung TV used in US). In that case, DVB will never work → use external set-top box.
- Contact Samsung support with your exact model number (e.g., UE55NU7100).
Would you like a simplified one-page printable guide or a remote control button sequence to fix this quickly?
If your Samsung TV is displaying a "DVB Select - Type Error," it typically indicates a conflict in the tuner settings or an issue with the signal source (like an antenna or satellite). This error often appears when the TV tries to access a digital broadcast (DVB) type—such as DVB-T (Terrestrial), DVB-S (Satellite), or DVB-C (Cable)—that is either not connected or improperly configured in the settings.
//www.reddit.com/r/techsupport/">Reddit's r/techsupport or the Samsung Community.
Title: Help! Samsung TV showing "DVB Select - Type Error" – How to fix? dvb select type error samsung tv
Body:Hi everyone, I'm running into a "DVB Select - Type Error" on my Samsung TV and can't seem to get past it. It usually pops up when I try to scan for channels or switch to the TV source. What I've tried so far:
Checked the antenna/cable connections to make sure they're tight.
Tried changing the source back to "TV," but sometimes the Broadcasting menu is grayed out.
Does anyone know if this is a software bug or a hardware issue with the tuner?I’ve heard that a "soft reset" (holding the power button on the remote for 10 seconds) or a factory reset through the service menu might help, but I don't want to lose all my settings if there's an easier fix. Errors related to DVB (Digital Video Broadcasting) on
If you've solved this before, please let me know which settings I should check! TV Model: [Insert your model number here, e.g., QN90A] Quick Fixes to Try Right Now
Power Cycle (The "Soft Reset"): While the TV is on, hold the Power button on your remote until the TV turns off and then back on again (usually about 10 seconds).
Change Source: Navigate to Menu > Connected Devices > Source and ensure it is set to TV before attempting to access the "Broadcasting" settings.
Update Software: Go to Settings > Support > Software Update > Update Now to ensure a bug isn't causing the error. DVB-T2 is widely used for terrestrial HDTV in
Factory Reset: As a last resort, go to Settings > General & Privacy > Reset (Default PIN is 0000). DVB TV Problems - JustAnswer
Since this is a technical support issue rather than a request for an academic paper, the following guide provides the technical breakdown, causes, and fixes for this specific error.
✅ Step 3 – Manual channel scan with correct parameters
- Menu → Broadcasting → Expert Settings.
- Manual Tuning → set:
- System: DVB-T2 (preferred if available)
- Bandwidth: 8 MHz (most regions) or 6 MHz (e.g., Brazil, Japan if using ISDB-T)
- Channel: Start from lowest frequency
2. Perform a Fresh Channel Scan
- Menu > Broadcasting > Auto Tuning (or Auto Program)
- Choose the correct Signal Source (Air/Antenna, Cable, or Satellite)
- Start scan