Fujitsu Irmc Default Password |best| -

The default login credentials for the Fujitsu Integrated Remote Management Controller (iRMC) are:  Username: admin Password: admin  Important Security Review 

Using default credentials poses a significant security risk to your server infrastructure. 

Change Immediately: You should change the default password during the initial setup to prevent unauthorized remote access to the server's hardware.

Resetting Credentials: If the password has been changed and forgotten, you can reset it without a reboot using an IPMI tool (like ipmitool on Linux/ESXi) or Fujitsu's IPMIVIEW utility for Windows.

Remote Management: The iRMC typically operates over Port 443 (HTTPS) by default for web interface operations. 

How to reset iRMC admin password on Fujitsu PRIMERGY servers

Fujitsu Integrated Remote Management Controller (iRMC) provides out-of-band management for PRIMERGY and PRIMEQUEST servers. Access to this interface is secured by credentials that have evolved from static defaults to unique, server-specific identifiers. Default Credentials by Generation fujitsu irmc default password

The default username for nearly all Fujitsu iRMC generations is admin. However, the password varies significantly depending on the age of the hardware:

Legacy Systems (iRMC S2, S3, S4): Older systems often shipped with the static default password admin.

Modern Systems (iRMC S5, S6): Current servers use unique passwords to comply with modern security standards. Locating Unique Default Passwords

For modern servers, the unique password can be found in two physical locations:

System ID Card: A pull-out plastic tag on the front of the server containing a barcode and a password typically prefixed with "Admin-" followed by 12 characters (e.g., Admin-4CkNxNZqWoOK).

Chassis Label: On smaller servers where a card is not present, a label is attached to the top cover. The default login credentials for the Fujitsu Integrated

💡 Key Note: The entire string, including the "Admin-" prefix, constitutes the password. It is strictly case-sensitive. Resetting or Changing the Password

If the default password fails or has been forgotten, you can reset it through several methods. Organizations can also refer to the Fujitsu PRIMERGY Security Overview for broader server hardening strategies. Using IPMITool (Local OS Access)

If you have access to the server's operating system (Linux or Windows), use the ipmitool utility to reset the admin password directly. Command: ipmitool user set password 2 .

User ID 2: This is the default ID for the "admin" user on Fujitsu hardware. Using ServerView Installation Manager (SVIM)

If the OS is unreachable, boot from the ServerView Installation Manager ISO. Open an x-term window and execute the same ipmitool command to regain access. Guidance for this and other tools is available through Fujitsu Support Downloads. Password Complexity Requirements

Starting with iRMC S6, new passwords must meet strict criteria: Minimum length of 12 characters. ✅ These are the factory defaults for most

Must include at least three of the following: lowercase letters, uppercase letters, digits, or special characters. Troubleshooting Common Issues

Character Confusion: Characters like capital "I" and lowercase "l" can look identical. Fujitsu recommends using a smartphone to scan the barcode on the ID card to retrieve the exact string.

"Unknown Error" at Login: On iRMC S6 (firmware 2.06S and lower), entering incorrect credentials may trigger a generic "Unknown Error" instead of a "Login Failed" message.

Manual Recovery: If you are using specialized hardware like the HyperScale appliance, you can find specific recovery steps on the Commvault Community. Peer-led technical discussions on Experts Exchange also provide legacy server support.

6.1 Immediate Actions (Day 1)

| Step | Command / Action | | :--- | :--- | | Change default password | Web: Configuration → Users → admin → Set new strong password (min 12 chars)
CLI via SSH: set /system1/account1 password=NewComplex!Pass | | Disable unused services | Disable HTTP, FTP, and SSH if not needed. Use HTTPS only. | | Set IPMI access restrictions | ipmitool lan set 1 access on → Then limit to specific IP ranges. |

Default Login Credentials

| Field | Default Value | |----------------|----------------------------| | Username | admin | | Password | admin |

✅ These are the factory defaults for most iRMC S2, S3, S4, S5, and newer versions unless changed by hardware customization or previous setup.

Keyboard Layout Issues

If you are typing the unique password from the sticker manually, ensure your keyboard is set to the correct language layout (e.g., US vs. UK). It is often safer to copy and paste the password if viewing a digital manifest.

Method B: Changing via iRMC CLI (SSH)

1. Enable SSH on iRMC (default is often disabled for security).
2. Connect via SSH: ssh admin@<iRMC_IP>
3. Use the command:

   set /system1/account1 password="YourNewStrongPassword"
   

   (Note: Account1 usually refers to admin account, but verify via show /system1/account*)
4. Save configuration: save

Security checklist after regaining access

• Immediately change default password to a strong, unique one.
• Enable/require secure access (HTTPS, disable HTTP/Telnet).
• Restrict management network access via firewall or VLAN.
• Confirm the iRMC firmware is up to date.
• Remove or rotate any credentials found on asset labels when decommissioning or reusing hardware.