Hi Sharp Dvr Reset Password New __exclusive__ May 2026

Modern Hi Sharp units have a built-in recovery tool on the login screen. Step 1: Go to the DVR login interface on your monitor. Step 2: Click on "Forgot Password" or "Retrieve Password". Step 3: Navigate to the "Dynamic Code" page. Step 4: Take a clear photo or screenshot of this page.

Step 5: Send this photo, along with your Model Number and Serial Number, to sales@hisharp.com.tw or your local distributor [0.5.3]. 2. Default Credentials

If the DVR was recently factory reset or is brand new, try the factory defaults: Username: admin Password: 123456 [0.5.7]

Other common defaults: 000000, 111111, or leave the password field blank. 3. Physical Hardware Reset (Last Resort)

If software methods fail, you may need to access the motherboard. hi sharp dvr reset password new

Battery Removal: Power off the DVR and remove the CMOS battery (the small silver coin-shaped battery) for 5–10 minutes. This often resets the system clock and may revert the password to default [0.5.11, 0.5.14].

Reset Button: Check the motherboard for a small physical button labeled "Reset" or "RST". Hold it down for 15 seconds while powering the device back on [0.5.5, 0.5.13]. 📋 Information You Will Need

Before contacting support, have these details ready from the sticker on the bottom of the device: Model Number (e.g., HS-HF6321) Serial Number (S/N) Device Date (The current date shown on the DVR's screen)

What is the specific Model Number on the bottom of the unit? Modern Hi Sharp units have a built-in recovery

Do you see a QR code or a Dynamic Code page when you click "Forgot Password"? Is the DVR currently connected to the internet?

I can provide more tailored steps or help you find the specific Hi Sharp Support contact for your region.

2. Use the “Forgot Password” or security question feature

On newer Hi Sharp models (or those with updated firmware):

  1. On the DVR’s local login screen, click Forgot Password or a small question‑mark icon.
  2. You may be asked to answer a security question you set earlier.
  3. Alternatively, the system may show a reset code (e.g., a string of numbers).
    • Note that code.
    • Contact Hi Sharp support or use their password reset tool (some brands offer a PC utility to generate a reset key from that code).

3. Method 1 – Using the Master Unlock Code (Most Common)

Hi Sharp DVRs often have a master password generated by a tool using the device’s serial number and date. On the DVR’s local login screen, click Forgot

Steps:

  1. Power on the DVR and connect a monitor/mouse.
  2. At the login screen, enter any wrong password 3–5 times until a “Forgot password?” or “Unlock” button appears.
  3. Write down the code displayed (often a 6-digit or alphanumeric string).
  4. Contact Hi Sharp support or use a third-party DVR password reset tool (e.g., “Hi Sharp Password Generator” – search online).
  5. Enter the generated unlock code into the DVR.
  6. You’ll be prompted to set a new password.

⚠️ Some newer models require a reset file via USB – contact support.

4. Use manufacturer/service mode (model-specific)

Method 1: The "Date Generator" Method (Most Common)

This method works on older and some newer Hi-Sharp models. The DVR generates a temporary password based on the date displayed on the screen.

Steps:

  1. Look at the monitor screen connected to your DVR. Note the date displayed (e.g., 2024-05-20).
  2. You need to calculate a code or use a generic Master Password based on that date.
  3. Try the following common Master Passwords:
    • Common Code 1: 345678 (Try this first)
    • Common Code 2: 000000 or 000001
    • Common Code 3: hsharpxx (where xx is the day of the month, e.g., hsharp01)

If those do not work: Hi-Sharp systems often use a specific algorithm. You may need to download a "Hi-Sharp Password Calculator" or "Hi-Sharp Key Generator" (often available on CCTV technician forums or the official Hi-Sharp support site if they have one in your region). You input the date shown on the DVR into the calculator, and it gives you a temporary reset code.

1. Try default credentials first