Resetting a Parrot MKi9200 without the original wireless remote is typically not possible through standard menus, as the remote is the primary way to navigate settings. However, you can use these alternative methods depending on your vehicle's setup: JustCarKits 1. Steering Wheel Controls (UNIKA Interface) If your car has a Parrot UNIKA
interface installed, you can navigate the menu using your factory steering wheel buttons. JustCarKits Access the Menu : Press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back Navigate to Settings Track Forward button to scroll to "Settings". Perform Factory Reset Phone/Accept button to enter "Settings". Advanced Settings and select it. Factory Reset and confirm with the The unit will reboot and clear all paired devices. JustCarKits 2. Hard Reset via Power Cycle
While this won't always delete paired phones, it can clear temporary glitches or a "frozen" screen. JustAnswer Disconnect Power
: Remove the car battery terminal or disconnect the Parrot control box (usually hidden behind the dashboard) for at least 10 minutes to allow the capacitors to discharge. Check Wiring
: If the unit "forgets" settings every time you turn the car off, the red (permanent 12V) and orange (ignition) wires may need to be swapped. JustAnswer 3. Firmware Update
Updating the firmware via a USB drive can sometimes force a memory wipe. JustCarKits Prepare a USB stick with the latest firmware from the official Parrot support site
Plug it into the MKi9200's USB cable. If the unit detects the update, it may overwrite existing data and reset the device. JustCarKits 4. Clearing "Memory Full" Errors If you are trying to reset because of a "Memory Full" message but cannot access the menu:
How to reset a Parrot MKi9200 without the remote - JustCarKits
Steps to reset a Parrot MKi9200 without the remote
Warning: resetting removes all paired phones, settings, saved numbers and call logs.
If the menu is inaccessible or the unit is unresponsive:
If you want to specifically unpair one phone instead of full reset:
If the wording differs slightly on your firmware, look for equivalent items: Settings → System/Unit → Reset/Factory reset.
Related search suggestions provided.
How to Reset Your Parrot MKi9200 Without a Remote If you have lost your remote control or the battery has died, you might find yourself locked out of your Parrot MKi9200 settings. Because this system relies almost entirely on its wireless RF remote for menu navigation, performing a factory reset without it is difficult—but not impossible if you have the right hardware or a bit of patience. The Short Answer: Can You Reset Without a Remote?
Standard factory resets for the Parrot MKi9200 strictly require the remote control to access the Settings > Advanced Settings > Factory Reset menu. However, there are two primary workarounds depending on your car's setup:
Steering Wheel Controls (Unika Interface): If your car uses the Parrot Unika interface to link your steering wheel buttons to the Parrot system, you can navigate the menus without the original remote.
Hard Reboot (Battery Disconnect): While not a "factory reset" that wipes data, disconnecting the unit from power for one hour can resolve some software glitches and "reboot" the system. Method 1: Using the Unika Steering Wheel Interface how do i reset my parrot mki9200 without remote
If your installer integrated the Parrot system with your car’s factory steering wheel buttons, you can use a specific sequence to enter the menu and trigger a reset.
Enter the Menu: Rapidly press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back.
Navigate to Settings: Once the menu appears on the MKi9200 screen, use the Track Forward button to scroll until you see "Settings".
Access Advanced Settings: Press your steering wheel's Phone/Accept button to enter the menu. Scroll down to "Advanced Settings" and press Phone/Accept again.
Trigger Factory Reset: Navigate to Factory Reset and confirm with the Phone/Accept button. The unit will reboot and clear its memory. Method 2: The "Memory Full" Emergency Reset
If you are trying to reset because you see a "Memory Full" error and cannot pair new phones, some users have reported success with a physical button combination if they still have access to the screen's control box or older firmware versions.
The Command: Press and hold the Green (Answer), Red (End Call), and Center Jog Wheel (if your model has an integrated one) buttons simultaneously for approximately 10 seconds.
The Result: The screen should go blank and emit a beep, indicating that the paired device list has been wiped. Method 3: Troubleshooting a "Dead" Remote
Before giving up on the remote, check if it simply needs a re-sync rather than a full system reset. Often, a remote isn't "broken," it just lost its pairing with the blue electronic box.
Replace the Battery: The remote uses a standard CR2032 battery. Ensure it is inserted correctly and that the metal contacts are touching the battery. Re-pair the Remote: Turn on your car's ignition.
Within the first 2 minutes of boot-up, simultaneously press and hold the Answer (Green), End (Red), and Play/Pause buttons.
Continue pressing them until the screen displays "Pairing Remote". Pro-Tips for Persistent Issues
Wiring Check: If your Parrot forgets settings every time you turn off the car, it likely isn't a reset issue but a wiring problem. You may need to swap the red and orange wires on the Parrot harness to ensure the unit receives constant power for its memory.
Replacement Parts: If the remote is truly lost, note that official replacements are increasingly rare. You may find used units on marketplaces like eBay or specialized retailers like JustCarKits.
Do you have steering wheel buttons available, or are you looking to buy a replacement remote to regain control? JustCarKitshttps://www.justcarkits.co.uk
How to reset a Parrot MKi9200 without the remote - JustCarKits
How to Reset a Parrot MKi9200 Without a Remote The Parrot MKi9200 Resetting a Parrot MKi9200 without the original wireless
is designed to be controlled almost entirely through its wireless remote. If your remote is lost or broken, performing a standard factory reset—which usually requires navigating the on-screen menus—is difficult but not impossible through alternative manual methods. 1. The Hard Reboot (Power Cycling)
The simplest way to clear temporary glitches without a remote is a hard reboot. This does not delete your paired devices but can resolve "frozen" screens or connection issues.
Disconnect Power: Locating and disconnecting the main blue control box from the car's wiring for about one hour can force the system to reboot.
Battery Disconnect: Alternatively, you can disconnect the vehicle's battery for a similar period to achieve a system-wide reset. 2. Manual Clear (Memory Full Fix)
If you are trying to reset because of a "Memory Full" error, there is a specific button combination that can wipe saved data without navigating menus. This is often necessary when you cannot pair new devices.
The "3-Button" Press: While the unit is powered on, press and hold the Green, Red, and Center Jog Wheel buttons simultaneously for approximately 10 seconds.
Confirmation: If successful, the screen should go blank and emit a beep, indicating that all saved data and paired devices have been wiped. 3. Software Update Reset
Performing a firmware update via the USB port can sometimes reset the device to factory defaults as part of the installation process.
USB Update: You can download the update tool from the Parrot Software Update page and load the update files onto a USB stick.
Automatic Detection: In some cases, plugging the USB stick into the
's music cable will trigger an update prompt automatically, though this often still requires a remote "click" to confirm. 4. Steering Wheel Control Alternative
If your vehicle has a steering wheel interface (like the Parrot UNIKA) installed, you may be able to use your car's existing buttons to navigate the menu to Settings > Advanced Settings > Factory Settings. Summary of Reset Options Method Requirement Hard Reboot Clears temporary errors Physical access to control box or car battery 3-Button Hold Wipes all paired devices Access to the screen buttons Firmware Flash Reinstalls system software USB stick and PC
Parrot MKi9200 Remote Not Connecting How To Fix? - JustAnswer
Resetting a Parrot MKi9200 without its original wireless remote is difficult because the device is designed to be controlled almost entirely through that interface. However, depending on your vehicle's setup, there are a few workarounds. JustCarKits 1. Using a Steering Wheel Interface (UNIKA) If your car has a Parrot UNIKA
interface installed, you can navigate the menus using your steering wheel buttons. JustCarKits Access the Menu : Press the following sequence on your steering wheel: Track Forward, Track Back, Track Forward, Track Back Track Forward button to scroll to "Settings". Phone/Accept Call button to enter menus. Advanced Settings > Factory Reset and confirm with the Phone button. JustCarKits 2. Hard Reboot (Power Cycle)
If you do not have steering wheel controls, you cannot perform a software factory reset. You can, however, force the unit to "reboot" to resolve temporary glitches. JustAnswer Disconnect Power
: Remove the unit’s power supply by disconnecting the blue control box for at least : This will reboot the system but will clear paired devices or internal memory. JustAnswer 3. Clearing "Memory Full" Errors Power on the MKi9200 and make sure the unit is not in a call
If your goal is to clear memory because you cannot pair a new phone, there is a specific button combination that works if the unit is semi-responsive: Combination : Press and hold the Green (Call) Center Jog Wheel buttons simultaneously for about 10 seconds
: If successful, the screen will go blank and beep, wiping the saved pairing data. Summary Table: Reset Methods Requirement UNIKA Interface Steering wheel buttons Full Factory Reset Button Combo Physical screen buttons Wipes paired devices Power Cycle Access to control box Soft reboot (no data loss) : If your remote is simply unresponsive, try replacing the CR2032 battery
first, as they typically only last 12–18 months. If the remote is lost, you may need to source a replacement remote to regain full access to the settings menu. JustCarKits or a guide on how to update the firmware via USB to possibly clear the memory? How to use parrot mki 9200 without remote - JustAnswer
Review: Resetting the Parrot MKi9200 Without the Remote Rating: ★★☆☆☆
I recently bought a used car that had a Parrot MKi9200 already installed. The system worked fine, but the previous owner didn't leave the wireless remote control, and the Bluetooth was paired to their old phones, meaning I couldn't connect mine.
I spent hours online trying to figure out how to do a "hard reset" or factory reset using just the screen and the steering wheel controls. Here is the conclusion I came to:
The Bad News: It seems impossible to fully factory reset the MKi9200 without the remote. The "Settings" menu—where the "Restore Factory Settings" option lives—is navigable, but the specific reset function is often blocked or requires a specific key combination that only exists on the remote.
I tried holding down the jog wheel, combinations of the red and green buttons on the screen, and disconnecting the battery for an hour. None of it cleared the paired devices list.
The Workaround (How I fixed it): Since I couldn't reset the memory, I had to use the "Delete All Pairs" method, but you need a phone already connected to do it. Since I couldn't connect my phone, I was stuck.
Eventually, I bought a cheap generic replacement remote on an auction site for about $15. The moment I put batteries in that remote, I was able to hold the red and green buttons down simultaneously to trigger the hardware reset.
Verdict: If you don't have the remote, you are essentially locked out of the system's administration functions. If you are in this situation, don't waste time trying button combos on the screen; just buy a replacement remote or check if your local car audio shop has a spare they can lend you for 30 seconds to wipe the memory.
The Parrot MKi9200 is a robust Bluetooth car kit, but like any electronic device, it can freeze, fail to pair, or develop audio glitches. The standard method to fix this involves using the remote control to access the settings menu.
If you have lost your remote or it has broken, you cannot perform a software-based reset via the on-screen menu. However, you can perform a hardware (factory) reset. This will erase all paired phones, the phonebook, and custom settings, returning the unit to its out-of-the-box state.
Warning: This process will delete all your data on the MKi9200. Proceed only if you are willing to lose your saved pairings and settings.
The MKi9200 consists of three parts: the screen, the microphone, and the control box (a black metal box roughly the size of a deck of cards).
This is the most critical step.
If you just want to connect a new phone:
Turn your car's ignition to the ACC or ON position so the Parrot screen lights up. Look at the control box. You will see a small hole labeled "Update" or simply a pinhole next to the USB port/slots. Inside this hole is a tactile button.