Phison Ps225107ps2307 Mptool |best|

The PS2251-07 (also known as PS2307) is a common Phison USB 3.0 controller found in many Kingston and Toshiba drives. When these drives fail—often appearing as "Read-Only" or "2307 PRAM"—the Phison MPALL (Multi-Port ALL-in-one) production tool is used to reflash the firmware and restore functionality. Prerequisites & Tools

To perform a repair, you generally need three components from a resource like USBDev.ru:

MPALL Software: Versions like v3.70.0E or v5.03.0A are frequently recommended for the PS2251-07.

Burner File (BN): A small loader (e.g., BN07*.BIN) that prepares the controller for the firmware.

Firmware File (FW): The actual operating code (e.g., FW07*.BIN). The specific file depends on your flash memory type (TLC, MLC, or eD3). General Recovery Process phison ps225107ps2307 mptool

Identify Details: Use a tool like ChipGenius or Flash Drive Information Extractor to confirm the controller is exactly PS2251-07 and to identify the specific NAND memory chip. Configuration (MPParamEdit_F1.exe):

Launch the parameter editor and select Basic Setting -> New Setting. Set the Controller to PS2251-07.

In the Flash Setting tab, enable "Do ISP" and browse for your specific Burner (BN) and Firmware (FW) files.

Ensure Preformat (Low Level Format) is checked if the drive is corrupted. Flashing: The PS2251-07 (also known as PS2307) is a

Open MPALL_F1_xxx.exe, click Update to detect the drive, and then Start to begin the process.

Warning: If the drive is not detected, you may need to manually put it into Test Mode by shorting specific pins on the controller chip (data bus pins) before plugging it in. Troubleshooting Common Errors

2307 PRAM: Indicates the controller is in a "panic" state with no firmware loaded. Reflashing with MPALL is the primary fix.

Slow Speed Post-Repair: If the drive works but is extremely slow, it usually means the firmware version used was not the optimal match for the NAND memory; trying a newer or different FW version can help. Back up data first – MPTool erases everything

Write Protection: If standard tools fail, Phison Format & Restore is a simpler user-level utility that can sometimes clear protection without a full reflash. Phison PS2251-07 (PS2307) Firmware [BN07*.BIN, FW07*.BIN]

Step-by-Step: Using the MP Tool (PS2251-07)

Warning: This will wipe all data on the drive permanently. Do not proceed if you need the files.

Part 4: A Practical MPTool Workflow for PS2307

Assume you have the correct MPTool version (e.g., MPALL v3.71.0A for PS2307).

  1. Back up data first – MPTool erases everything.
  2. Run MPParamEdit_F1.exe (or F2 for fixed disk modes).
  3. Create a new parameter file:
    • Controller: PS2251-07
    • Flash Type: Click "Auto Detect" – if it fails, select from list based on GetInfo report.
    • Mode: 3 (Removable disk – standard), 21 (CD-ROM + storage), 7 (Fixed disk – makes Windows see it as local drive).
  4. Partition Settings: For fake capacity drives, set "Format" and "Low Level Format" – this restores true size.
  5. Firmware: Browse to FW_07_*.bin (included in tool pack). For PS2307, you often need both ISP_..._BL.bin and ISP_..._FW.bin.
  6. Save the parameter file.
  7. Open MPALL_F1_90A_vxxx_All.exe (main tool).
  8. Load your parameter file.
  9. Click "Start".

Interesting outcome: A previously fake 2TB drive will emerge as 32GB or 64GB – the true NAND size.

Core features

  • Firmware flashing: Upload controller firmware (.bin/.fw) to device.
  • Configuration (SPD/Config): Edit controller parameters (HCT, LBA mapping, vendor ID/product ID, features like UASP or partition behavior).
  • Manufacturing actions: Mass-production workflows (SN/ID writing, capacity report, trimming).
  • Low-level formatting and secure erase.
  • Smart tests: Read/write/verify tests and error reporting; some versions support speed calibration and retention checks.
  • Logs: Basic operation logs; verbosity varies by build.