Reset Impressora Samsung Laser Ml 1860 1865 1867

⚠️ Important: This reset procedure is for the toner cartridge chip counter (useful after refilling toner). It does not reset the permanent waste toner counter or fuser life, which require special tools or a mainboard reset.

Métodos rápidos (ordem recomendada)

1. Reinício simples (soft reset)

• Desligue a impressora pelo botão de energia.
• Aguarde 10–15 segundos.
• Ligue novamente.
  Uso: corrigir travamentos menores.

2. Reset eletrônico / Hard reset (sem menu)

• Com a impressora ligada, desconecte o cabo de alimentação da tomada por 30–60 segundos.
• Reconecte e ligue.
  Uso: quando a impressora não responde ao botão de energia.

3. Reset do contador de toner / waste toner (procedimento manual comum)

• Ligue a impressora.
• Abra a tampa frontal e remova o cartucho de toner.
• Localize a alavanca do sensor de toner (depende do modelo; pode ser um pequeno pino ou botão plástico).
• Pressione e segure a alavanca/botão por 5–10 segundos enquanto recoloca o cartucho.
• Feche a tampa e reinicie a impressora.
  Resultado: reinicia contador e mensagem de toner/waste pode desaparecer.
  Nota: se não houver alavanca acessível, o reset pode requerer procedimento de menu/serviço.

4. Reset via painel de controle (se aplicável)

• Ligue a impressora.
• No painel, navegue para Menu > System Setup > Restore Defaults (ou similar).
• Confirme “Yes” para restaurar configurações de fábrica.
  Uso: restaurações de configurações e redes.

5. Reset de serviço (Service Mode) — para usuários avançados / técnicos

• ATENÇÃO: modo de serviço altera configurações internas e deve ser usado somente por técnicos. Pode exigir código de acesso.
• Procedimento típico (varia por firmware):
  • Desligue a impressora.
  • Pressione e segure os botões “Stop/Cancel” e “Power” (ou combinação similar) enquanto liga a impressora até entrar no modo de serviço.
  • Navegue até a opção “Clear NVM” / “Initialize” / “Waste Toner Reset” e execute.
  • Saia e reinicie.
• Se você não tiver o combo exato para seu modelo, consulte manual técnico ou assistência autorizada.

Step-by-Step Instructions:

1. Turn off the printer using the power button on the front panel. Unplug the power cord from the wall outlet and wait 30 seconds.
2. Open the front cover (the door where the toner cartridge lives).
3. Remove the toner cartridge and set it aside on a clean piece of paper (avoid direct light).
4. Check for obstructions – Look inside for any paper jams or loose debris.
5. Plug the printer back in but do NOT turn it on yet.
6. Press and hold the “Cancel” button (the circular arrow or “X” button – the exact label varies by regional model). On the ML-1865, this is often the right-most button.
7. While holding Cancel, press the Power button once. Keep holding Cancel for another 5 seconds after the lights flash, then release both.
8. Watch the LED sequence:
   • All LEDs will blink once.
   • The green “Ready” LED will stay on.
   • The red “Error” LED may blink.
9. Open and close the front cover five times quickly (within 10 seconds). On some models, it’s three times. If five doesn’t work, retry with three slow, deliberate opens/closes.
10. The printer will make grinding noises – this is normal. It is resetting the gear counter.
11. Wait 20 seconds. The green light should stop blinking and stay solid.
12. Reinstall the toner cartridge and close the front cover.
13. Print a test page: Hold the Cancel button for 10 seconds.

Does this work on refilled cartridges? Yes, 80% of the time. However, if your printer has a new third-party chip, you may need Method 2.

Avisos importantes

• Reset de contador de toner/waste pode permitir impressão temporária, mas não altera nível físico de toner; use com responsabilidade.
• Reset de fábrica apaga configurações de rede e personalizações.
• Desconecte da rede e faça backup de configurações importantes antes de reset de fábrica.

Método 3: Utilizando o Software de Assistência da Samsung

A Samsung oferece software de assistência que pode ajudar a diagnosticar e resolver problemas, incluindo a realização de um reset.

1. Baixe o software: Visite o site oficial da Samsung e procure pelo software de assistência para sua impressora (por exemplo, Samsung Printer Diagnostics).
2. Instale e execute o software: Siga as instruções para instalar e executar o software.
3. Siga as instruções do software: O software guiará você através do processo de diagnóstico e reparo, que pode incluir opções de reset.

Conclusão

Resetar a impressora Samsung Laser ML 1860, 1865 ou 1867 pode ser uma solução eficaz para vários problemas técnicos. No entanto, é sempre recomendável entrar em contato com o suporte técnico da Samsung ou um profissional de manutenção se você não se sentir confortável em realizar esses procedimentos ou se os problemas persistirem após o reset. Lembre-se de que o reset de fábrica apagará todas as configurações personalizadas, então é uma boa ideia documentá-las antes, se possível.

In the quiet corner of Lucas’s home office sat the Samsung Laser ML-1860 Reset Impressora Samsung Laser ML 1860 1865 1867

, a sleek monochrome workhorse that had faithfully churned out invoices for years. But today, the machine had decided to go on strike. A stubborn blinking red light mocked Lucas from the control panel, and every attempt to print his urgent tax documents was met with an eerie silence.

Lucas tried the "standard" dance first. He performed a soft reset, powering down the machine and unplugging it for a full minute to drain its memory. When he plugged it back in, the motor whirred—a hopeful sound—only to be cut short by that same rhythmic red blink.

Frustrated, he turned to the internet's collective wisdom. He learned about the "cat and mouse game" between printer manufacturers and users, where small chips and resistors are used to track page counts. His printer wasn't "broken"; it just thought its life was over because a counter had reached an arbitrary number.

Following a guide for a hard reset, Lucas tried the "secret handshake":

He held the Print Screen button (located above the power button) for about 10 seconds. ⚠️ Important : This reset procedure is for

The LED flashed once, a signal that the internal counters were attempting to reset themselves to 100%.

For more stubborn issues, he found others had used a "Tech Menu" combination—a rapid sequence of Menu, Back, Left, Right, OK, and Stop—to access the deep settings of the machine and "Clear All Memory".

As a last resort for a separate "won't power on" issue he’d read about, some brave souls even replaced a 57-cent capacitor on the circuit board, saving their printers from the landfill for the price of a candy bar.

Lucas stuck to the button sequence. After the third try, the blinking red light finally surrendered, turning a solid, steady green. With a triumphant clack-clack-clack, the ML-1860 pulled a fresh sheet of paper and printed his documents perfectly. The strike was over, and the old laser printer lived to fight another day.

Method 3: Manual Chip Reset (Hardware)

The ML-1860/1865/1867 use a small PCB chip on the side of the toner cartridge (MLT-D105S or MLT-D105L). You can: Métodos rápidos (ordem recomendada)

1. Remove toner cartridge.
2. Locate the chip (small green board with 3–4 metal contacts).
3. Disconnect the chip from the cartridge’s own contact spring (if possible) or cover the leftmost pin with a small piece of non-conductive tape (insulating tape).
4. Reinsert cartridge – printer will see “Unknown toner” and may reset.
5. Remove tape after reset if it works.

This is a hack. Not all chips allow it.

For macOS / Linux:

Samsung did not provide deep reset software for macOS. Use Method 1 or Method 3.

2. Soft reset (clear temporary errors)

Steps:

1. Turn off the printer.
2. Unplug power cable for 30 seconds.
3. Plug back in and turn on.
4. If error persists → proceed to hard reset.

---

Q: My ML-1867 shows “Toner Low” but still prints. Should I reset?

A: No. Wait until it says “Toner Empty” or stops printing. Resetting early wastes the chip’s reset cycles.