Urmet 1131 Manual Full ((exclusive)) ❲Proven

Urmet 1131 is a classic analog door phone (intercom) handset used widely across Europe and Australia. Since it is a "universal" compatible model, the manual is primarily a guide for wiring diagrams to replace older or different brand systems. 🔑 Key Technical Specifications System Type:

4+n analog systems (meaning 4 common wires plus 1 call wire per apartment). Compatibility:

Designed to replace most traditional handsets (e.g., Terraneo, Golmar, Fermax) by matching terminal functions. Terminals: Speaker (Earphone) Electronic Call Signal (or for buzzer) Microphone Common Ground Door Opener (Lock release) 🛠️ Common Wiring Scenarios

The "Full Manual" typically includes a conversion table. If you are replacing a non-Urmet brand, you usually map the wires as follows: Urmet 1131 Terminal Other Brands (Common) Terminal 1 or 2 Microphone Terminal 2 or 3 Terminal 3 or 4 Terminal 5 or 6 CA (Electronic) Terminal 7 or C 💡 Pro-Tips for Installation Buzzer vs. Electronic Tone:

The 1131 supports both. If your old system used a mechanical "buzz," you wire to terminal . If it’s a modern melodic tone, use The "Jumper":

Some versions have a jumper to split or join the ground (Terminals 6 and 10). If the door lock doesn't trigger, check if this bridge is needed. Volume Adjustment:

There are often small potentiometers inside to balance the "sidetone" (feedback) so you don't hear your own voice too loudly. 📂 Manual Access You can find the official technical PDF on the Urmet Australia support pages. Search specifically for the "1131/1 Universal Door Phone Manual"

to get the full conversion charts for over 30 different brands. Are you looking to replace an existing handset , or are you troubleshooting

a specific issue like the microphone or door strike not working?

The 1131 handset typically uses 5 active terminals. If you are replacing an old unit, it is highly recommended to label each wire before disconnecting it. Description 1 Speech In Speaker (Receives audio from the entrance panel) 2 Speech Out Microphone (Sends audio to the entrance panel) 6 Common Ground/Common return for the system 9 Lock Door Release (Triggers the electric lock) CA Call Electronic call signal (The buzzer/speaker ring)

Note: Some diagrams refer to a Terminal 10, but it is often linked to Terminal 6 (Common) in standard installations. Key Installation Notes

System Type: This handset is designed for Electronic Call systems. It is not directly compatible with older buzzer-call systems unless specifically adapted.

Wire Identification: In older buildings, wire colors may not follow a standard pattern. If wires are not labeled, you may need a multimeter or professional assistance to identify the "Common" and "Call" lines.

Replacement: If the existing handset is missing, you can often find wiring diagrams for your specific building system on professional sites like Intercoms R Us.

Universal Alternatives: If the 1131 is unavailable, the Urmet 1130/16 is a common "Universal" replacement that can be configured for various systems, though it requires specific jumper settings. Basic Operation

Answering: Lift the handset to establish two-way communication.

Door Release: Press the dedicated "Key" button while the handset is off the hook to unlock the door.

Ending Call: Replace the handset on the cradle to terminate the connection.

For official technical documents and certifications, you can visit the Urmet Professional Tools page.

Are you replacing an existing Urmet 1131 or attempting to troubleshoot a specific issue like low audio or the door lock not working? Urmet 1131 (Electronic Call) - Intercoms R Us Page 1. Urmet 1131 (Electronic Call) Terminals. Intercoms R Us urmet-1131 - device.report

Title: Comprehensive User & Technical Manual: Urmet 1131 Series Mains Power Supply Unit

Document Version: 1.0 (Compiled for User Reference) Applicable Models: Urmet 1131 Series (Including variants 1131/0, 1131/1, 1131/2)

Problem 1: "I hear the doorbell, but the screen stays black."

Manual Reference: Section 6.2 – "Video Troubleshooting." Solution:

Check the voltage at terminals A/B during a call. It should dip but stay above 18V.
Inspect the internal ribbon cable connecting the LCD to the main board. The full manual shows an exploded view of how to reseat it.
The camera in the door station (Urmet 1130 or 1132) might be faulty.

Section 1: Physical Description and Parts

The manual starts with a labeled diagram. Key components include:

Monitor Screen: 4.3" TFT LCD.
Call Button (Key symbol): Answers the door.
Talk Button: Activates the microphone.
Door Lock Button (Padlock symbol): Opens the electric strike.
Volume/ Brightness Trimmers: Usually located behind a small flap or under the handset.

4. Physical Connections (Typical)

| Terminal | Signal | |----------|--------| | L1 / L2 | 2-wire BUS (to Urmet riser / power supply) | | TEL LINE | Incoming PSTN line (from Telecom socket) | | TEL SET | Optional parallel telephone | | NO / C / NC | Relay 1 (e.g., electric lock) | | NO2 / C2 / NC2 | Relay 2 (e.g., auxiliary) | | +12V / GND | Optional external power (if not powered via BUS) |

Enter Programming Mode

Connect an analog telephone to the “TEL SET” port.
Pick up the handset.
Dial the programming access code (default: #1234 – verify in your manual).
You will hear a confirmation tone (double beep).

1. Technical Specifications

Before installation, ensure your power supply and monitoring equipment match the camera’s requirements.